日本
- HRC40~72 淬火鋼： 直接在淬火鋼、模具鋼、高速鋼上鑽孔，免去退火與再熱處理。
- 3 刃設計： 高硬度鑽頭為 3 刃（微型為 2 刃），孔徑精度與孔面粗糙度優異。
- 刀尖角： 刀尖角 140°，負角刃形，右刃、h6 柄徑公差。
- 尺寸範圍： 短型 ALD 鍍層 φ1~12、標準型 ALT 鍍層 φ0.8~6、微型短型 / 標準型 ALT 鍍層 φ0.1~2。
- 公差： 短型為負公差（φD 0 / −0.02）；其他型號公差設定不同，請留意。
- 搭配 SP 定位： 與 TOGLON 高硬度 SP 併用，提高孔位精度。
使用注意事項
- 機台： 請使用高剛性機台；與一般鑽頭相比推力為 2~5 倍，不需要特別的高速主軸。
- 刀把： 建議使用把持力高的銑刀夾頭或熱縮刀把；小徑、高精度孔或 20D 以上長刀具需要高偏擺精度。
- 切削液： 建議水溶性切削液或油霧，並需充足的壓力與流量；切屑回流時可改由 45° 以內斜向供液。
- 中心孔： 孔徑 2 mm 以下或孔深 5D 以上時，必須先以 TOGLON 高硬度 SP 90° 加工定位孔，選擇最大倒角徑為鑽頭直徑 0.6~1.4 倍的尺寸，定位深度為鑽頭直徑的 50%。
- 啄鑽： 孔深 3D 以上需使用啄鑽（G83），啄鑽同時兼具排屑與冷卻刃口的作用。
規格型式
- IWATA TOGLON 高硬度鑽頭 短型 ALD 鍍層
- IWATA TOGLON 高硬度鑽頭 標準型 ALT 鍍層
- IWATA TOGLON 微型高硬度鑽頭 短型 ALT 鍍層
- IWATA TOGLON 微型高硬度鑽頭 標準型 ALT 鍍層
規格表
IWATA TOGLON 高硬度鑽頭 短型 ALD 鍍層
| 型號 | 直徑 φD | 柄徑 φd | 溝長 FL | 有效長 ℓ1 | 全長 L | 詢價 |
|---|---|---|---|---|---|---|
| TGHDS1CBALD | 1 | 3 | 6 | 7.9 | 50 | |
| TGHDS1.1CBALD | 1.1 | 3 | 7 | 9.1 | 50 | |
| TGHDS1.2CBALD | 1.2 | 3 | 7 | 9.2 | 50 | |
| TGHDS1.3CBALD | 1.3 | 3 | 8 | 10.4 | 50 | |
| TGHDS1.4CBALD | 1.4 | 3 | 8 | 10.5 | 50 | |
| TGHDS1.5CBALD | 1.5 | 3 | 9 | 11.7 | 50 | |
| TGHDS1.6CBALD | 1.6 | 3 | 10 | 12.8 | 50 | |
| TGHDS1.7CBALD | 1.7 | 3 | 10 | 13 | 50 | |
| TGHDS1.8CBALD | 1.8 | 3 | 11 | 14.1 | 50 | |
| TGHDS1.9CBALD | 1.9 | 3 | 11 | 14.3 | 50 | |
| TGHDS2CBALD | 2 | 4 | 12 | 15.4 | 60 | |
| TGHDS2.1CBALD | 2.1 | 4 | 12 | 15.6 | 60 | |
| TGHDS2.2CBALD | 2.2 | 4 | 13 | 16.7 | 60 | |
| TGHDS2.3CBALD | 2.3 | 4 | 13 | 16.9 | 60 | |
| TGHDS2.4CBALD | 2.4 | 4 | 14 | 18 | 60 | |
| TGHDS2.5CBALD | 2.5 | 4 | 14 | 18.2 | 60 | |
| TGHDS2.6CBALD | 2.6 | 4 | 14 | 18.3 | 60 | |
| TGHDS2.7CBALD | 2.7 | 4 | 16 | 20.5 | 60 | |
| TGHDS2.8CBALD | 2.8 | 4 | 16 | 20.6 | 60 | |
| TGHDS2.9CBALD | 2.9 | 4 | 16 | 20.8 | 60 | |
| TGHDS3CBALD | 3 | 4 | 16 | 20.9 | 60 | |
| TGHDS3.1CBALD | 3.1 | 4 | 18 | 23.1 | 60 | |
| TGHDS3.2CBALD | 3.2 | 4 | 18 | 23.2 | 60 | |
| TGHDS3.3CBALD | 3.3 | 4 | 18 | 23.4 | 60 | |
| TGHDS3.4CBALD | 3.4 | 4 | 20 | 25.6 | 60 | |
| TGHDS3.5CBALD | 3.5 | 4 | 20 | 25.7 | 60 | |
| TGHDS3.6CBALD | 3.6 | 4 | 21 | 26.8 | 60 | |
| TGHDS3.7CBALD | 3.7 | 4 | 21 | 27 | 60 | |
| TGHDS3.8CBALD | 3.8 | 4 | 22 | 28.1 | 60 | |
| TGHDS3.9CBALD | 3.9 | 4 | 22 | 28.3 | 60 | |
| TGHDS4CBALD | 4 | 4 | 22 | 28.4 | 60 | |
| TGHDS4.1CBALD | 4.1 | 6 | 24 | 30.6 | 60 | |
| TGHDS4.2CBALD | 4.2 | 6 | 24 | 30.7 | 60 | |
| TGHDS4.3CBALD | 4.3 | 6 | 24 | 30.9 | 60 | |
| TGHDS4.4CBALD | 4.4 | 6 | 24 | 31 | 60 | |
| TGHDS4.5CBALD | 4.5 | 6 | 24 | 31.2 | 60 | |
| TGHDS4.6CBALD | 4.6 | 6 | 25 | 32.3 | 60 | |
| TGHDS4.7CBALD | 4.7 | 6 | 25 | 32.5 | 60 | |
| TGHDS4.8CBALD | 4.8 | 6 | 25 | 32.6 | 60 | |
| TGHDS4.9CBALD | 4.9 | 6 | 25 | 32.8 | 60 | |
| TGHDS5CBALD | 5 | 6 | 26 | 33.9 | 60 | |
| TGHDS5.1CBALD | 5.1 | 6 | 26 | 34.1 | 60 | |
| TGHDS5.2CBALD | 5.2 | 6 | 26 | 34.2 | 60 | |
| TGHDS5.3CBALD | 5.3 | 6 | 26 | 34.4 | 60 | |
| TGHDS5.4CBALD | 5.4 | 6 | 26 | 34.5 | 60 | |
| TGHDS5.5CBALD | 5.5 | 6 | 28 | 36.7 | 60 | |
| TGHDS5.6CBALD | 5.6 | 6 | 28 | 36.8 | 60 | |
| TGHDS5.7CBALD | 5.7 | 6 | 28 | 37 | 60 | |
| TGHDS5.8CBALD | 5.8 | 6 | 28 | 37.1 | 60 | |
| TGHDS5.9CBALD | 5.9 | 6 | 28 | 37.3 | 60 | |
| TGHDS6CBALD | 6 | 6 | 28 | 37.4 | 60 | |
| TGHDS6.1CBALD | 6.1 | 8 | 31 | 40.6 | 80 | |
| TGHDS6.2CBALD | 6.2 | 8 | 31 | 40.7 | 80 | |
| TGHDS6.5CBALD | 6.5 | 8 | 31 | 41.2 | 80 | |
| TGHDS6.8CBALD | 6.8 | 8 | 34 | 44.6 | 80 | |
| TGHDS6.9CBALD | 6.9 | 8 | 34 | 44.8 | 80 | |
| TGHDS7CBALD | 7 | 8 | 34 | 44.9 | 80 | |
| TGHDS7.5CBALD | 7.5 | 8 | 34 | 45.7 | 80 | |
| TGHDS7.8CBALD | 7.8 | 8 | 37 | 49.1 | 80 | |
| TGHDS7.9CBALD | 7.9 | 8 | 37 | 49.3 | 80 | |
| TGHDS8CBALD | 8 | 8 | 37 | 49.4 | 80 | |
| TGHDS8.5CBALD | 8.5 | 10 | 37 | 50.2 | 100 | |
| TGHDS8.6CBALD | 8.6 | 10 | 40 | 53.3 | 100 | |
| TGHDS8.7CBALD | 8.7 | 10 | 40 | 53.5 | 100 | |
| TGHDS8.8CBALD | 8.8 | 10 | 40 | 53.6 | 100 | |
| TGHDS9CBALD | 9 | 10 | 40 | 53.9 | 100 | |
| TGHDS9.5CBALD | 9.5 | 10 | 40 | 54.7 | 100 | |
| TGHDS9.6CBALD | 9.6 | 10 | 40 | 54.8 | 100 | |
| TGHDS9.7CBALD | 9.7 | 10 | 43 | 58 | 100 | |
| TGHDS9.8CBALD | 9.8 | 10 | 43 | 58.1 | 100 | |
| TGHDS10CBALD | 10 | 10 | 43 | 58.4 | 100 | |
| TGHDS10.3CBALD | 10.3 | 12 | 43 | 58.9 | 110 | |
| TGHDS10.4CBALD | 10.4 | 12 | 43 | 59 | 110 | |
| TGHDS10.5CBALD | 10.5 | 12 | 43 | 59.2 | 110 | |
| TGHDS10.8CBALD | 10.8 | 12 | 47 | 63.6 | 110 | |
| TGHDS11CBALD | 11 | 12 | 47 | 63.9 | 110 | |
| TGHDS11.5CBALD | 11.5 | 12 | 47 | 64.7 | 110 | |
| TGHDS11.8CBALD | 11.8 | 12 | 47 | 65.1 | 110 | |
| TGHDS12CBALD | 12 | 12 | 51 | 69.4 | 110 |
IWATA TOGLON 高硬度鑽頭 標準型 ALT 鍍層
| 型號 | 直徑 φD | 柄徑 φd | 溝長 FL | 有效長 ℓ1 | 全長 L | 庫存 | 詢價 |
|---|---|---|---|---|---|---|---|
| TGHDR0.8CBALT | 0.8 | 3 | 4.8 | 9.6 | 50 | 標準庫存 | |
| TGHDR0.9CBALT | 0.9 | 3 | 5.4 | 10.8 | 50 | 標準庫存 | |
| TGHDR1CBALT | 1 | 3 | 6 | 12 | 50 | 標準庫存 | |
| TGHDR1.1CBALT | 1.1 | 3 | 6.6 | 13.2 | 50 | 標準庫存 | |
| TGHDR1.2CBALT | 1.2 | 3 | 7.2 | 14.4 | 50 | 標準庫存 | |
| TGHDR1.3CBALT | 1.3 | 3 | 7.8 | 15.6 | 50 | 標準庫存 | |
| TGHDR1.4CBALT | 1.4 | 3 | 8.4 | 16.8 | 50 | 標準庫存 | |
| TGHDR1.5CBALT | 1.5 | 3 | 9 | 18 | 50 | 標準庫存 | |
| TGHDR1.6CBALT | 1.6 | 3 | 9.6 | 19.2 | 50 | 標準庫存 | |
| TGHDR1.7CBALT | 1.7 | 3 | 10.2 | 20.4 | 50 | 標準庫存 | |
| TGHDR1.8CBALT | 1.8 | 3 | 10.8 | 21.6 | 50 | 標準庫存 | |
| TGHDR1.9CBALT | 1.9 | 3 | 11.4 | 22.8 | 50 | 標準庫存 | |
| TGHDR2CBALT | 2 | 4 | 12 | 24 | 60 | 標準庫存 | |
| TGHDR2.1CBALT | 2.1 | 4 | 12.6 | 25.2 | 60 | 標準庫存 | |
| TGHDR2.2CBALT | 2.2 | 4 | 13.2 | 26.4 | 60 | 標準庫存 | |
| TGHDR2.3CBALT | 2.3 | 4 | 13.8 | 27.6 | 60 | 標準庫存 | |
| TGHDR2.4CBALT | 2.4 | 4 | 14.4 | 28.8 | 60 | 標準庫存 | |
| TGHDR2.5CBALT | 2.5 | 4 | 15 | 30 | 60 | 標準庫存 | |
| TGHDR2.6CBALT | 2.6 | 4 | 15.6 | 31.2 | 60 | 標準庫存 | |
| TGHDR2.7CBALT | 2.7 | 4 | 16.2 | 32.4 | 60 | 標準庫存 | |
| TGHDR2.8CBALT | 2.8 | 4 | 16.8 | 33.6 | 60 | 標準庫存 | |
| TGHDR2.9CBALT | 2.9 | 4 | 17.4 | 34.8 | 60 | 標準庫存 | |
| TGHDR3CBALT | 3 | 4 | 18 | 36 | 60 | 標準庫存 | |
| TGHDR3.1CBALT | 3.1 | 4 | 18.6 | 37.2 | 80 | 標準庫存 | |
| TGHDR3.2CBALT | 3.2 | 4 | 19.2 | 38.4 | 80 | 標準庫存 | |
| TGHDR3.3CBALT | 3.3 | 4 | 19.8 | 39.6 | 80 | 標準庫存 | |
| TGHDR3.4CBALT | 3.4 | 4 | 20.4 | 40.8 | 80 | 標準庫存 | |
| TGHDR3.5CBALT | 3.5 | 4 | 21 | 42 | 80 | 標準庫存 | |
| TGHDR3.6CBALT | 3.6 | 6 | 21.6 | 43.2 | 100 | 標準庫存 | |
| TGHDR3.7CBALT | 3.7 | 6 | 22.2 | 44.4 | 100 | 標準庫存 | |
| TGHDR3.8CBALT | 3.8 | 6 | 22.8 | 45.6 | 100 | 標準庫存 | |
| TGHDR3.9CBALT | 3.9 | 6 | 23.4 | 46.8 | 100 | 標準庫存 | |
| TGHDR4CBALT | 4 | 6 | 24 | 48 | 100 | 標準庫存 | |
| TGHDR4.1CBALT | 4.1 | 6 | 24.6 | 49.2 | 100 | 標準庫存 | |
| TGHDR4.2CBALT | 4.2 | 6 | 25.2 | 50.4 | 100 | 標準庫存 | |
| TGHDR4.3CBALT | 4.3 | 6 | 25.8 | 51.6 | 100 | 標準庫存 | |
| TGHDR4.4CBALT | 4.4 | 6 | 26.4 | 52.8 | 100 | 標準庫存 | |
| TGHDR4.5CBALT | 4.5 | 6 | 27 | 54 | 100 | 標準庫存 | |
| TGHDR4.6CBALT | 4.6 | 6 | 27.6 | 55.2 | 100 | 標準庫存 | |
| TGHDR4.7CBALT | 4.7 | 6 | 28.2 | 56.4 | 100 | 標準庫存 | |
| TGHDR4.8CBALT | 4.8 | 6 | 28.8 | 57.6 | 100 | 標準庫存 | |
| TGHDR4.9CBALT | 4.9 | 6 | 29.4 | 58.8 | 100 | 標準庫存 | |
| TGHDR5CBALT | 5 | 6 | 30 | 60 | 100 | 標準庫存 | |
| TGHDR5.1CBALT | 5.1 | 6 | 30.6 | 61.2 | 120 | 標準庫存 | |
| TGHDR5.2CBALT | 5.2 | 6 | 31.2 | 62.4 | 120 | 標準庫存 | |
| TGHDR5.3CBALT | 5.3 | 6 | 31.8 | 63.6 | 120 | 標準庫存 | |
| TGHDR5.4CBALT | 5.4 | 6 | 32.4 | 64.8 | 120 | 標準庫存 | |
| TGHDR5.5CBALT | 5.5 | 6 | 33 | 66 | 120 | 標準庫存 | |
| TGHDR5.6CBALT | 5.6 | 8 | 33.6 | 67.2 | 120 | 接單生產 | |
| TGHDR5.7CBALT | 5.7 | 8 | 34.2 | 68.4 | 120 | 接單生產 | |
| TGHDR5.8CBALT | 5.8 | 8 | 34.8 | 69.6 | 120 | 標準庫存 | |
| TGHDR5.9CBALT | 5.9 | 8 | 35.4 | 70.8 | 120 | 標準庫存 | |
| TGHDR6CBALT | 6 | 8 | 36 | 72 | 120 | 標準庫存 |
IWATA TOGLON 微型高硬度鑽頭 短型 ALT 鍍層
| 型號 | 直徑 φD | 柄徑 φd | 溝長 FL | 有效長 ℓ1 | 全長 L | 詢價 |
|---|---|---|---|---|---|---|
| TGHMDS0.1CBALT | 0.1 | 3 | 0.6 | 0.7 | 50 | |
| TGHMDS0.15CBALT | 0.15 | 3 | 0.9 | 1.1 | 50 | |
| TGHMDS0.2CBALT | 0.2 | 3 | 1.2 | 1.4 | 50 | |
| TGHMDS0.25CBALT | 0.25 | 3 | 1.5 | 1.8 | 50 | |
| TGHMDS0.3CBALT | 0.3 | 3 | 1.8 | 2.1 | 50 | |
| TGHMDS0.4CBALT | 0.4 | 3 | 2.4 | 2.8 | 50 | |
| TGHMDS0.5CBALT | 0.5 | 3 | 3 | 3.5 | 50 | |
| TGHMDS0.6CBALT | 0.6 | 3 | 3.6 | 4.2 | 50 | |
| TGHMDS0.7CBALT | 0.7 | 3 | 4.2 | 4.9 | 50 | |
| TGHMDS0.8CBALT | 0.8 | 3 | 4.8 | 5.6 | 50 | |
| TGHMDS0.9CBALT | 0.9 | 3 | 5.4 | 6.3 | 50 | |
| TGHMDS1CBALT | 1 | 3 | 6 | 7 | 50 | |
| TGHMDS1.1CBALT | 1.1 | 3 | 6.6 | 7.7 | 50 | |
| TGHMDS1.2CBALT | 1.2 | 3 | 7.2 | 8.4 | 50 | |
| TGHMDS1.3CBALT | 1.3 | 3 | 7.8 | 9.1 | 50 | |
| TGHMDS1.4CBALT | 1.4 | 3 | 8.4 | 10.2 | 50 | |
| TGHMDS1.5CBALT | 1.5 | 3 | 9 | 10.5 | 50 | |
| TGHMDS1.6CBALT | 1.6 | 3 | 9.6 | 11.2 | 50 | |
| TGHMDS1.7CBALT | 1.7 | 3 | 10.2 | 11.9 | 50 | |
| TGHMDS1.8CBALT | 1.8 | 3 | 10.8 | 12.6 | 50 | |
| TGHMDS1.9CBALT | 1.9 | 3 | 11.4 | 13.3 | 50 | |
| TGHMDS2CBALT | 2 | 3 | 12 | 14 | 50 |
IWATA TOGLON 微型高硬度鑽頭 標準型 ALT 鍍層
| 型號 | 直徑 φD | 柄徑 φd | 溝長 FL | 有效長 ℓ1 | 全長 L | 詢價 |
|---|---|---|---|---|---|---|
| TGHMDR0.1CBALT | 0.1 | 3 | 0.6 | 1.3 | 50 | |
| TGHMDR0.15CBALT | 0.15 | 3 | 0.9 | 2 | 50 | |
| TGHMDR0.2CBALT | 0.2 | 3 | 1.2 | 2.6 | 50 | |
| TGHMDR0.25CBALT | 0.25 | 3 | 1.5 | 3.3 | 50 | |
| TGHMDR0.3CBALT | 0.3 | 3 | 1.8 | 3.9 | 50 | |
| TGHMDR0.4CBALT | 0.4 | 3 | 2.4 | 5.2 | 50 | |
| TGHMDR0.5CBALT | 0.5 | 3 | 3 | 6.5 | 50 | |
| TGHMDR0.6CBALT | 0.6 | 3 | 3.6 | 7.8 | 50 | |
| TGHMDR0.7CBALT | 0.7 | 3 | 4.2 | 9.1 | 50 | |
| TGHMDR0.8CBALT | 0.8 | 3 | 4.8 | 10.4 | 50 | |
| TGHMDR0.9CBALT | 0.9 | 3 | 5.4 | 11.7 | 50 | |
| TGHMDR1CBALT | 1 | 3 | 6 | 13 | 50 | |
| TGHMDR1.1CBALT | 1.1 | 3 | 6.6 | 14.3 | 50 | |
| TGHMDR1.2CBALT | 1.2 | 3 | 7.2 | 15.6 | 50 | |
| TGHMDR1.3CBALT | 1.3 | 3 | 7.8 | 16.9 | 50 | |
| TGHMDR1.4CBALT | 1.4 | 3 | 8.4 | 18.2 | 50 | |
| TGHMDR1.5CBALT | 1.5 | 3 | 9 | 19.5 | 50 | |
| TGHMDR1.6CBALT | 1.6 | 3 | 9.6 | 20.8 | 50 | |
| TGHMDR1.7CBALT | 1.7 | 3 | 10.2 | 22.1 | 50 | |
| TGHMDR1.8CBALT | 1.8 | 3 | 10.8 | 23.4 | 50 | |
| TGHMDR1.9CBALT | 1.9 | 3 | 11.4 | 24.7 | 50 | |
| TGHMDR2CBALT | 2 | 3 | 12 | 26 | 50 |
產品相關圖片
聯絡我們
感謝您對菱鵬的關注與支持！如果您有任何問題、建議或需要進一步瞭解我們的產品與服務，請隨時與我們聯絡。